Manual: H® ECO 🌱 Performance & Saving Fuel

Ultra-Rapid Installation of Ionic H® ECO 🌱 Performance & Saving Fuel Dry Cell Rubber Mounts in Just Minutes

(Recuperation of negative ions from infrared engine radiation, pumping back to engine power)

CARS, SUVS, BUSES, TRACTORS, TRUCKS, BOATS DIESEL ENGINES.

Mount the brown tube cut into several parts onto the bent hose. Never cut off any engine tube or parts. 

 

Use all rubbers to cover the end of the fuel pipe close to engine parts as is fuel filter, pressure pump, injectors.

 


FOR ENJOYING A SPORTS REGIME TUBE CAN ONLY BE OVERLAID POSITIVE CABLE. 

 

BIKES, CARS, SUVS, SQUAD, AIRCRAFTS, PETROL GASOLINE


FOR ENJOYING A SPORTS REGIME TUBE CAN ONLY BE OVERLAID POSITIVE CABLE.



ION GRILL IS FOR SPORTS MODE (not for fuel saving) MUST BE FITTED BEFORE AIR FILTER,
NOT BEHIND THE FILTER, AS IT CAN BE SUCKED INTO THE ENGINE!
(Sport grill is not included in basic package)


Does the H® Hyper Easy: Infra Quantum Ions pair effectively with Dry Cell HHO Kit HHO generators?

With our advanced H® Hyper Easy: Infra Quantum Ion Fuel Rubbers, decarbonization becomes unnecessary. For deep engine cleaning, we suggest using hydrogen only every 8,000-10,000 km, ideally during engine oil changes, to ensure optimal engine performance.

Can low temperature limit the function of Infra Quantum Ions?
At low temperatures under 0 °C, the function of the rubbers in the petrol and diesel engines may be limited. When the engine is heated to 80-100 °C, the rubbers start to receive infrared radiation from the engine and the fluid molecules start to shrink, which has a positive effect on reducing engine friction.

Fuel pressure pump, diesel fuel filter, breaking fluid pump, steering wheel pump all these parts create load and friction on the engine. By connecting more rubbers, further percentages of powerare obtained, resulting in reduced consumption and harmful emissions.

If you own new H® Hyper Easy: EFIE chip for OBD II OBD2.

HHO chip for hho kit

 

To remove the pin with the cable from the OBD2 connector, insert the end of the eject tool into the hole in the OBD2 slot and push firmly until the tray slides out. Using this tool you can safely remove the pin cable from the plug. Thanks


Schema OBD2 OBDII for plug of Blue HHO ChipOBD2 OBDII port for Blue HHO Chip

 

HHO CHIP OBD2 CAN, VPW,  ISO,  PWM


If you bought H® Hyper Easy: EFIE chip for OBD II OBD2 follow instructions:
To connect the two wires of the OBD2 connector correctly, send us the pictures of your OBD2 and we will send you the correct diagram in turn. The OBD2 for each vehicle type may be different and we need to see your pins inside the OBD2 port. You can see the attached sample.


sim circle PIN for smartphone


Signalisation

STANDBY MODE

STANDBY MODE
Standby LED blinks every 5-10 seconds. There is no signal from the vehicle’s computer. The device may not enter stand-by on some vehicles in which the ECU remains active after engine shut-off. This is normal and will not adversely effect operation. 

POWER ON MODE

POWER ON MODE
Power and Link LEDs are solid green. Auto Calibration tuning and ECU LEDs are solid or flashing. This indicates the device is connected and functioning properly.
CALIBRATING

CALIBRATING
Power LED is solid green LINK LED is flashing Auto Calibration tuning and ECU LEDs are solid or flashing. The device is in Auto-Calibration mode. During this time, your particular engine characteristics are being evaluated to generate an offset map. This allows the device to fine tune itself for optimum performance.

Every time if you make a minimal change to the rubbers, even moving the tube 1 cm or covering it with lead, the H® Hyper Easy: EFIE chip should be reset and drive minimum 8km and 30-50km to see new result. There is a significant change in the engine!

Get the best ionic rubber recuperating engine waste heat to save fuel, reduce emissions and dramatically increase performance.

Back to blog